OK Guys, the rose tutorial at long last. Had the pictures done for ages, just been waiting for this eye to allow me to spend long enough on the computer to put it all together. But after showing so many lovely crafters how to make them at the weekend demo and now there are so many subtle hints popping up around blogland that me thinks I'd better get my act together, so here we go................. 
The basic ingredients: Six petal punch (1" used here)
Dries clear Art Institute glue
Iridescent embossing powder
Versamark inkpad
Tweezers (an absolute must unless you have endless patience)
Patterned or plain paper (see notes at bottom)
Punch out three flowers for each rose. Brush versafine or other ink pad around the edges, dip into embossing powder and heat. Then crease each flower across the natural line between the petals so you can see six sections.
Following the crease lines, cut to the centre of one flower. Do the same on the second flower but cut one section out. Repeat on the third flower but cut out two sections (as one). You will then have five elements to make your rose.
Using the dries clear glue take the largest flower and overlap one petal onto the next at the cut section. Do the same with the next two graduating down in size, so you are left with five elements of 5,4,3,2,&1 petals.
When dry (allow a couple of minutes), using a pokey tool or cocktail stick curl each petal outwards. The single petal should be rolled into a funnel shape.
Cut the tips off the bottom of each section - don't worry about the hole in the bottom, this will be covered as you assemble your rose.
Using the same glue put a couple of 'blobs' onto the bottom of the four and three petaled sections, place the four petal onto into the largest, then the three petal section into the other two working down in size.
Next put some glue into the centre (the centre will now be the three petaled section) and arrange the two petal piece and finally the single petal - the roses are quite resilient, especially if you have embossed the edges so and you can push the pieces round until you are happy with the placements.
Punch out three flowers for each rose. Brush versafine or other ink pad around the edges, dip into embossing powder and heat. Then crease each flower across the natural line between the petals so you can see six sections.Following the crease lines, cut to the centre of one flower. Do the same on the second flower but cut one section out. Repeat on the third flower but cut out two sections (as one). You will then have five elements to make your rose.Using the dries clear glue take the largest flower and overlap one petal onto the next at the cut section. Do the same with the next two graduating down in size, so you are left with five elements of 5,4,3,2,&1 petals. When dry (allow a couple of minutes), using a pokey tool or cocktail stick curl each petal outwards. The single petal should be rolled into a funnel shape.Cut the tips off the bottom of each section - don't worry about the hole in the bottom, this will be covered as you assemble your rose.
Using the same glue put a couple of 'blobs' onto the bottom of the four and three petaled sections, place the four petal onto into the largest, then the three petal section into the other two working down in size.
Next put some glue into the centre (the centre will now be the three petaled section) and arrange the two petal piece and finally the single petal - the roses are quite resilient, especially if you have embossed the edges so and you can push the pieces round until you are happy with the placements. 
A few notes:
Double sided paper is best otherwise you will see a white middle petal - but you can always colour the reverse of the single centre section with an inkpad or other colour medium. I have tried all sorts of DP and find Daisy Bucket one of the very best as it is beautifully pliable, some DP can be stiff and will fold rather that curl. Good old copier paper also works very well.
The above rose is made from plain orange copier paper and heavily ebbossed with iridescent glitter. When making three roses, which I find the optimun number for a project, I like to make a couple from one side of the DP and one from the other to add contrast to the finished project. You can also create your own pattered paper to match your card by stamping and embossing the cut out flowers before assembling into your rose. Vellum also works very well and can be stamped to add interest. Embossing the edges with clear embossing powder works wonderfully on dark colours and looks like dewdrops.
I made the roses above from plain cream copier paper, brushed beige and green brilliance inkpads round the edges and embossed with detail clear powder.
The roses below were made from a patterned DP, the edges embossed with crystal embossing powder and stamens added - mine are from a garden centre which sells florist and cake decorating accessories. Equally you could use gems or brads, placing them inside with silicone.
I made the roses above from plain cream copier paper, brushed beige and green brilliance inkpads round the edges and embossed with detail clear powder.The roses below were made from a patterned DP, the edges embossed with crystal embossing powder and stamens added - mine are from a garden centre which sells florist and cake decorating accessories. Equally you could use gems or brads, placing them inside with silicone.
I hope this all makes sense and you can follow everything, but any questions please don't be afraid to mail me (link on my profile). Happy rose making and I'm expecting roses to be blooming all over blogland very soon.
No comments:
Post a Comment